GY-302 BH1750 Digital Light Intensity Sensor Module
Original price was: ₵40.00.₵35.00Current price is: ₵35.00.
Digital ambient light sensor for accurate light-intensity measurement in Arduino, ESP32, Raspberry Pi and IoT projects. The GY-302 uses the BH1750 sensor to provide direct illumination readings in lux through an I2C interface, eliminating the analogue calculations normally required with LDR sensors.
Sensor: BH1750FVI
Measurement: Light intensity in lux
Supply: 3V–5V DC
Interface: I2C
Range: Approx. 1–65,535 lux
ADC: 16-bit
I2C Address: 0x23 / 0x5C selectable
Best For: Smart lighting, agriculture, environmental monitoring, robotics and IoT projects
10 in stock
The GY-302 BH1750 Digital Light Intensity Sensor Module is a high-precision ambient light sensor designed to measure illumination directly in lux (lx). It uses the BH1750 digital light sensor and communicates with Arduino, ESP32, STM32, Raspberry Pi and other microcontrollers through the I2C interface.
Unlike basic LDR light sensors that provide an analogue resistance change, the BH1750 contains an integrated 16-bit ADC and provides digital light-intensity readings directly. This makes it easier to obtain consistent measurements for automatic lighting, environmental monitoring, smart agriculture and IoT applications.
The GY-302 supports a wide measurement range of approximately 1–65,535 lux, with high-resolution measurement modes capable of resolutions down to approximately 0.5 lux. Its spectral response is designed to approximate the sensitivity of the human eye, making it suitable for measuring visible ambient brightness.
The module also provides an ADDR pin, allowing selection between two I2C addresses so that two BH1750 sensors can be connected to the same I2C bus.
Technical Specifications
| Specification | Details |
|---|---|
| Module | GY-302 |
| Sensor IC | BH1750FVI |
| Sensor Type | Digital ambient light sensor |
| Measurement Unit | Lux (lx) |
| Module Supply Voltage | 3V–5V DC |
| Communication Interface | I2C |
| ADC Resolution | 16-bit |
| Standard Measurement Range | Approx. 1–65,535 lux |
| High-Resolution Mode | Down to approx. 0.5 lux resolution |
| I2C Addresses | 0x23 / 0x5C selectable |
| Pins | VCC, GND, SCL, SDA, ADDR |
| Output | Direct digital light-intensity reading |
| Typical Module Size | Approx. 18.5 × 13.9 mm |
| Compatible Platforms | Arduino, ESP32, ESP8266, STM32, Raspberry Pi |
Applications
- Automatic lighting systems
- Smart-home projects
- Solar-light controllers
- Weather and environmental monitoring
- Smart agriculture and greenhouse monitoring
- Automatic display brightness control
- IoT sensor systems
- Robotics
- STEM and educational projects
- Light-intensity data logging
Package Includes
1 × GY-302 BH1750 Light Intensity Sensor Module
1 × Pin Header
Related products
16-in-1 Sensor Module Kit for Arduino, ESP32 & Raspberry Pi
Expand your project possibilities instantly. This value-packed kit contains 16 of the most popular sensors for home automation and robotics. Instead of buying modules individually, get everything you need in one box.
-
Includes: DHT11 Temperature, Relay, Ultrasonic, Motion Sensor, and 12 more!
-
Compatibility: Works perfectly with Arduino Uno, Mega, Nano, and Raspberry Pi.
-
Perfect For: Learning how to read data and control devices.
433MHz RF Transmitter & Receiver Kit | Wireless Module for Arduino
Cut the cord. Go wireless. This kit includes one Transmitter and one Receiver. It is the simplest and most affordable way to send data wirelessly between two Arduinos up to 100 meters (with antenna).
-
Frequency: 433MHz
-
Includes: 1x Transmitter (Square), 1x Receiver (Rectangle)
-
Modulation: ASK (Amplitude Shift Keying)
-
Best For: Remote control cars, weather stations, and wireless switches.
DS3231 RTC Real-Time Clock Module
The DS3231 is a highly accurate I2C real-time clock (RTC) with an integrated temperature-compensated crystal oscillator (TCXO).
-
Chip: Maxim DS3231 (High Precision)
-
Memory: Built-in AT24C32 32K I2C EEPROM
-
Voltage: 3.3V – 5.5V DC
-
Interface: I2C (SCL, SDA)
-
Battery Backup: Holds time when power is off (Coin cell slot included)
-
Accuracy: Much higher than the standard DS1307
High Sensitivity Vibration Sensor Module (SW-1801P) | Shock & Shake Switch
Detect even the slightest tap. Unlike standard vibration sensors that require a hard shake, the SW-1801P High Sensitivity module can detect light knocks, impacts, and vibrations. Perfect for anti-theft alarms and "Smart Wake-Up" devices.
-
Sensor Type: SW-1801P (High Sensitivity Spring).
-
Output: Digital (High/Low).
-
Adjustable: Blue Potentiometer to set sensitivity trigger.
-
Best For: Anti-Theft Alarms, Earthquake Detection, and Smart Toys.
IR Infrared Obstacle Avoidance Sensor Module | FC-51 for Arduino
-
Detection Range: 2cm - 30cm (Adjustable).
-
Output: Digital Signal (LOW when obstacle detected).
-
Compatibility: Works directly with Arduino, ESP32, and Raspberry Pi.
-
Best For: Robot Cars, Smart Trash Cans, and Proximity Alarms.
Raindrop Sensor Module | Rain & Water Detector for Arduino
Build your own weather station. This sensor detects rain, snow, or water droplets. It consists of a large nickel-plated sensing board and a control module. When water hits the board, it sends a signal to your Arduino to close windows or sound an alarm.
-
Sensor Type: Resistive (Nickel-Plated Board).
-
Outputs: Digital (High/Low) and Analog (Rain Intensity).
-
Durability: Treated against oxidation for longer life.
-
Best For: Automatic Wipers, Smart Clotheslines, and Weather Stations.
Reviews
There are no reviews yet.