GY-302 BH1750 Digital Light Intensity Sensor Module
Original price was: ₵40.00.₵35.00Current price is: ₵35.00.
Digital ambient light sensor for accurate light-intensity measurement in Arduino, ESP32, Raspberry Pi and IoT projects. The GY-302 uses the BH1750 sensor to provide direct illumination readings in lux through an I2C interface, eliminating the analogue calculations normally required with LDR sensors.
Sensor: BH1750FVI
Measurement: Light intensity in lux
Supply: 3V–5V DC
Interface: I2C
Range: Approx. 1–65,535 lux
ADC: 16-bit
I2C Address: 0x23 / 0x5C selectable
Best For: Smart lighting, agriculture, environmental monitoring, robotics and IoT projects
10 in stock
The GY-302 BH1750 Digital Light Intensity Sensor Module is a high-precision ambient light sensor designed to measure illumination directly in lux (lx). It uses the BH1750 digital light sensor and communicates with Arduino, ESP32, STM32, Raspberry Pi and other microcontrollers through the I2C interface.
Unlike basic LDR light sensors that provide an analogue resistance change, the BH1750 contains an integrated 16-bit ADC and provides digital light-intensity readings directly. This makes it easier to obtain consistent measurements for automatic lighting, environmental monitoring, smart agriculture and IoT applications.
The GY-302 supports a wide measurement range of approximately 1–65,535 lux, with high-resolution measurement modes capable of resolutions down to approximately 0.5 lux. Its spectral response is designed to approximate the sensitivity of the human eye, making it suitable for measuring visible ambient brightness.
The module also provides an ADDR pin, allowing selection between two I2C addresses so that two BH1750 sensors can be connected to the same I2C bus.
Technical Specifications
| Specification | Details |
|---|---|
| Module | GY-302 |
| Sensor IC | BH1750FVI |
| Sensor Type | Digital ambient light sensor |
| Measurement Unit | Lux (lx) |
| Module Supply Voltage | 3V–5V DC |
| Communication Interface | I2C |
| ADC Resolution | 16-bit |
| Standard Measurement Range | Approx. 1–65,535 lux |
| High-Resolution Mode | Down to approx. 0.5 lux resolution |
| I2C Addresses | 0x23 / 0x5C selectable |
| Pins | VCC, GND, SCL, SDA, ADDR |
| Output | Direct digital light-intensity reading |
| Typical Module Size | Approx. 18.5 × 13.9 mm |
| Compatible Platforms | Arduino, ESP32, ESP8266, STM32, Raspberry Pi |
Applications
- Automatic lighting systems
- Smart-home projects
- Solar-light controllers
- Weather and environmental monitoring
- Smart agriculture and greenhouse monitoring
- Automatic display brightness control
- IoT sensor systems
- Robotics
- STEM and educational projects
- Light-intensity data logging
Package Includes
1 × GY-302 BH1750 Light Intensity Sensor Module
1 × Pin Header
Related products
433MHz RF Transmitter & Receiver Kit | Wireless Module for Arduino
Cut the cord. Go wireless. This kit includes one Transmitter and one Receiver. It is the simplest and most affordable way to send data wirelessly between two Arduinos up to 100 meters (with antenna).
-
Frequency: 433MHz
-
Includes: 1x Transmitter (Square), 1x Receiver (Rectangle)
-
Modulation: ASK (Amplitude Shift Keying)
-
Best For: Remote control cars, weather stations, and wireless switches.
DS18B20 Waterproof Temperature Sensor Probe | Stainless Steel Digital Thermometer
Measure liquid temperature with digital precision. This is the waterproof version of the famous DS18B20 sensor. Encased in a stainless steel tube, it is perfect for measuring water, soil, or air temperature in harsh environments.
-
Range: -55°C to +125°C
-
Interface: 1-Wire Digital (Requires only 1 pin)
-
Cable Length: 1 Meter
-
Best For: Aquariums, boilers, soil temperature, and cold chain monitoring.
Flame Sensor Module (YG1006) | Infrared Fire Detector for Arduino
-
Sensor Type: YG1006 NPN Phototransistor (High Speed).
-
Detection Range: Up to 1 meter (depending on flame size).
-
Spectrum: 760nm - 1100nm (Invisible IR light).
-
Best For: Fire Fighting Robots, Smart Kitchen Alarms, and Safety Systems.
HC-SR04 Ultrasonic Sensor Module | Distance Measurement for Arduino
Give your robot eyes. The HC-SR04 uses sonar (sound waves) to measure distance, just like a bat. It is the standard sensor for obstacle avoidance robots and water level monitoring systems.
-
Range: 2cm to 400cm (4 Meters)
-
Accuracy: 3mm
-
Pins: VCC, Trig, Echo, GND
-
Best For: Obstacle avoiding cars, reverse parking sensors, and tank level detection.
IRF520 MOSFET Driver Module (0-24V) | PWM Motor & LED Controller
-
Max Load: 24V DC / < 5A.
-
Control Voltage: 3.3V or 5V (PWM Compatible).
-
Output: Pulse Width Modulation (Speed/Dimming control).
-
Best For: LED Strips, Small DC Fans, and Solenoids.
MQ-135 Air Quality & Hazardous Gas Sensor Module | CO2, Smoke, Ammonia
Detect smoke and dangerous gases instantly. The MQ-135 is the most versatile gas sensor for air quality monitoring. It detects a wide range of gases including Ammonia, Sulfide, Benzene, Smoke, and CO2. Perfect for "Smart Home" safety systems and environmental monitoring.
- Gases Detected: NH3, NOx, Alcohol, Benzene, Smoke, CO2.
-
Output: Analog (Gas Concentration) and Digital (Alarm Trigger).
-
Warm-up Time: ~20 seconds.
-
Best For: Air Quality Monitors, Smoke Alarms, and Industrial Safety.
MQ-3 Alcohol Sensor Module | Breathalyzer & Ethanol Detector
-
Detects: Alcohol, Ethanol, Benzine.
-
Sensitivity: Adjustable via Blue Potentiometer.
-
Warm-up: Heater requires ~20 seconds.
-
Best For: Breathalyzers, Drunk Driving Alarms, and Industrial Monitoring.
Reviews
There are no reviews yet.