GY-302 BH1750 Digital Light Intensity Sensor Module
Original price was: ₵40.00.₵35.00Current price is: ₵35.00.
Digital ambient light sensor for accurate light-intensity measurement in Arduino, ESP32, Raspberry Pi and IoT projects. The GY-302 uses the BH1750 sensor to provide direct illumination readings in lux through an I2C interface, eliminating the analogue calculations normally required with LDR sensors.
Sensor: BH1750FVI
Measurement: Light intensity in lux
Supply: 3V–5V DC
Interface: I2C
Range: Approx. 1–65,535 lux
ADC: 16-bit
I2C Address: 0x23 / 0x5C selectable
Best For: Smart lighting, agriculture, environmental monitoring, robotics and IoT projects
10 in stock
The GY-302 BH1750 Digital Light Intensity Sensor Module is a high-precision ambient light sensor designed to measure illumination directly in lux (lx). It uses the BH1750 digital light sensor and communicates with Arduino, ESP32, STM32, Raspberry Pi and other microcontrollers through the I2C interface.
Unlike basic LDR light sensors that provide an analogue resistance change, the BH1750 contains an integrated 16-bit ADC and provides digital light-intensity readings directly. This makes it easier to obtain consistent measurements for automatic lighting, environmental monitoring, smart agriculture and IoT applications.
The GY-302 supports a wide measurement range of approximately 1–65,535 lux, with high-resolution measurement modes capable of resolutions down to approximately 0.5 lux. Its spectral response is designed to approximate the sensitivity of the human eye, making it suitable for measuring visible ambient brightness.
The module also provides an ADDR pin, allowing selection between two I2C addresses so that two BH1750 sensors can be connected to the same I2C bus.
Technical Specifications
| Specification | Details |
|---|---|
| Module | GY-302 |
| Sensor IC | BH1750FVI |
| Sensor Type | Digital ambient light sensor |
| Measurement Unit | Lux (lx) |
| Module Supply Voltage | 3V–5V DC |
| Communication Interface | I2C |
| ADC Resolution | 16-bit |
| Standard Measurement Range | Approx. 1–65,535 lux |
| High-Resolution Mode | Down to approx. 0.5 lux resolution |
| I2C Addresses | 0x23 / 0x5C selectable |
| Pins | VCC, GND, SCL, SDA, ADDR |
| Output | Direct digital light-intensity reading |
| Typical Module Size | Approx. 18.5 × 13.9 mm |
| Compatible Platforms | Arduino, ESP32, ESP8266, STM32, Raspberry Pi |
Applications
- Automatic lighting systems
- Smart-home projects
- Solar-light controllers
- Weather and environmental monitoring
- Smart agriculture and greenhouse monitoring
- Automatic display brightness control
- IoT sensor systems
- Robotics
- STEM and educational projects
- Light-intensity data logging
Package Includes
1 × GY-302 BH1750 Light Intensity Sensor Module
1 × Pin Header
Related products
DHT11 Temperature and Humidity Sensor Module | Digital Weather Station
The #1 sensor for weather projects. The DHT11 is the most affordable way to measure ambient temperature and humidity. It provides calibrated digital signal output, making it perfect for automatic fan controllers and weather stations.
-
Measures: Temperature (0-50°C) & Humidity (20-90%)
-
Interface: Single Wire Digital (Easy Arduino Connection)
-
Includes: 3-Pin Breakout Board + Jumper Wires (Check your stock to confirm wires!)
-
Ideal For: Smart homes, greenhouses, and environment monitoring.
DS3231 RTC Real-Time Clock Module
The DS3231 is a highly accurate I2C real-time clock (RTC) with an integrated temperature-compensated crystal oscillator (TCXO).
-
Chip: Maxim DS3231 (High Precision)
-
Memory: Built-in AT24C32 32K I2C EEPROM
-
Voltage: 3.3V – 5.5V DC
-
Interface: I2C (SCL, SDA)
-
Battery Backup: Holds time when power is off (Coin cell slot included)
-
Accuracy: Much higher than the standard DS1307
High Sensitivity Vibration Sensor Module (SW-1801P) | Shock & Shake Switch
Detect even the slightest tap. Unlike standard vibration sensors that require a hard shake, the SW-1801P High Sensitivity module can detect light knocks, impacts, and vibrations. Perfect for anti-theft alarms and "Smart Wake-Up" devices.
-
Sensor Type: SW-1801P (High Sensitivity Spring).
-
Output: Digital (High/Low).
-
Adjustable: Blue Potentiometer to set sensitivity trigger.
-
Best For: Anti-Theft Alarms, Earthquake Detection, and Smart Toys.
IRF520 MOSFET Driver Module (0-24V) | PWM Motor & LED Controller
-
Max Load: 24V DC / < 5A.
-
Control Voltage: 3.3V or 5V (PWM Compatible).
-
Output: Pulse Width Modulation (Speed/Dimming control).
-
Best For: LED Strips, Small DC Fans, and Solenoids.
MQ-135 Air Quality & Hazardous Gas Sensor Module | CO2, Smoke, Ammonia
Detect smoke and dangerous gases instantly. The MQ-135 is the most versatile gas sensor for air quality monitoring. It detects a wide range of gases including Ammonia, Sulfide, Benzene, Smoke, and CO2. Perfect for "Smart Home" safety systems and environmental monitoring.
- Gases Detected: NH3, NOx, Alcohol, Benzene, Smoke, CO2.
-
Output: Analog (Gas Concentration) and Digital (Alarm Trigger).
-
Warm-up Time: ~20 seconds.
-
Best For: Air Quality Monitors, Smoke Alarms, and Industrial Safety.
MQ-3 Alcohol Sensor Module | Breathalyzer & Ethanol Detector
-
Detects: Alcohol, Ethanol, Benzine.
-
Sensitivity: Adjustable via Blue Potentiometer.
-
Warm-up: Heater requires ~20 seconds.
-
Best For: Breathalyzers, Drunk Driving Alarms, and Industrial Monitoring.
SW-420 Vibration Sensor Module | Adjustable Impact & Shake Switch
- Sensor Type: SW-420 (Normally Closed).
- Output: Digital (High/Low).
- Sensitivity: Adjustable via Blue Potentiometer.
- Best For: Anti-Theft Alarms, Smart Cars, and Impact Detection.
Reviews
There are no reviews yet.